Unibody and Body-on-Frame Damage
V
Start with how your vehicle is built. In a unibody, the norm for modern cars, the frame and the body skeleton are manufactured together as one complete unit, Kelley Blue Book explains. Most pickups, plus a handful of large SUVs and vans, still use body-on-frame construction, with the body set on a separate ladder frame.
The difference shows up in the damage. With a body-on-frame vehicle, Kelley Blue Book says, frame damage is damage to the ladder frame. On a unibody, the structure itself is the frame: Volkswagen's repair statement lists frame rails, floor structures and A- and B-pillars among unibody structural components built to work together.
- Unibody: one unit of frame and body skeleton
- Body-on-frame: the body rides on a ladder frame
- Most pickups still use a ladder frame
- A, B and C pillars can count as unibody frame damage
- I-CAR: damaged suspension mounts matter on both designs
Collision Services
Warning Signs After a Hard Hit
V
Compare the car with how it looked and drove before the collision. Kelley Blue Book counts door, trunk and hood seams that are no longer consistent or even, doors that start sticking or won't close smoothly, a steering pull that continues after an alignment, and strange or uneven tire wear as possible signs of frame damage.
No single sign settles the question. Michelin traces pulling to causes such as misalignment, a low tire on one side or a sticking caliper. I-CAR's curriculum adds that a vehicle that left the road surface may have steering or suspension damage not immediately apparent on a visual inspection. Scheduling an estimate gets the car diagnosed in person.
- Walk-around: seams at doors, hood or trunk gone uneven
- Doors: sticking suddenly or not closing smoothly
- Driving: pulling that persists after an alignment
- Tires: abnormal or uneven tread wear
- Michelin: misalignment most often causes pulling
Request an Estimate
Measuring the Structure Against Factory Specs
V
Newer vehicles leave less room for error. I-CAR says they have tighter tolerances than older vehicles of the same model and often use non-adjustable door hinges, suspension mounting locations and sensor mounting locations, so if the structure misses the automaker's measurements, those parts may not fit or function as designed.
So the structure is measured against the automaker's published dimensions. I-CAR says the old rule-of-thumb tolerances no longer hold for all vehicles, and it credits three-dimensional measuring with an accurate picture of the damage and a before-and-after record of the straightening. Readings can also differ with the suspension loaded or unloaded, I-CAR adds.
- Length, width and height behind every measuring point (I-CAR)
- GM: use three-dimensional measuring equipment, its procedures say
- Engine in or out can change measurements, I-CAR says
- I-CAR: automakers often set exact measurements, not ranges
- I-CAR: non-adjustable sensor mounts need the structure right
Certified Repairs
Straighten, Section or Replace: What Automakers Allow
V
The automaker's repair procedures set what is allowed; I-CAR calls them service specifications, not recommendations. Heat, I-CAR warns, can permanently damage certain metals, and GM allows controlled heat on mild and high-strength low alloy steel only if it does not exceed 650°C (1200°F), at most twice for up to 90 seconds.
I-CAR defines a kink as a sharp bend with a small radius over a short distance, and its rule calls for replacing kinked parts. Bent parts may be candidates for repair unless the automaker says otherwise, yet I-CAR says many of them also require replacement. Sectioning, a partial replacement of a damaged part, needs a published automaker procedure, per I-CAR.
- Damaged crush zones cannot be straightened, says I-CAR
- Toyota prohibits heat repair of body and frame components
- GM: heat not recommended on ultra-high-strength or dual-phase steel
- Hyundai: no heat at all on ultra-high-strength structural steel
- Honda: factory-seam replacement of steel parts is preferred
Why Choose Us
Corrosion Protection and Final Checks
V
A structural repair is not finished when the metal is straight. I-CAR notes that repairs disturb many areas of corrosion protection, creating hot spots that, left untreated, lead to corrosion and potentially a repair failure. Its curriculum also has the wheel alignment checked after the repairs are completed.
For its part, the Ocala shop lists structural fixes, including frame alignment and unibody repairs, among its collision services. Its certifications page names an I-CAR Gold Class Certified Team, Certified Assured Performance, Nissan Collision Repair Network, Kia Recognized Collision Repair Center, Hyundai Recognized Collision Repair Center and a ProFirst Collision Repair Facility certification from American Honda.
- I-CAR: automaker specs generally cover sealer, foams and cavity waxes
- Foam fillers normally go in before refinishing (I-CAR)
- Cavity waxes normally follow refinish, before trim (I-CAR)
- I-CAR: wrong timing can cause refinish defects
- Lifetime warranty on all repairs performed at Jenkins Collision Centers
Contact the Collision Team